The LTR x86 instruction stands for load task register and is used in operating systems that support multitasking. LTR is supported only in protected mode and long mode, not in real mode or virtual 8086 mode. It must be executed when the Current Privilege Level (CPL) is 0, and therefore cannot be used by application programs. LTR loads the special x86 task register with a segment selector that points to a task state segment (TSS). After executing the LTR instruction, the TSS pointed to by the argument is marked busy, but no hardware task switch occurs.
* v
* t
* e
Attributes | Values |
---|
rdf:type
| |
rdfs:label
| - Load task register (en)
- 작업 적재 레지스터 (ko)
|
rdfs:comment
| - LTR x86 명령어는 load task register 즉 작업 적재 레지스터를 의미하며 멀티태스킹을 지원하는 운영 체제에서 사용된다. LTR은 보호 모드와 롱 모드에서만 지원되며 리얼 모드나 가상 86모드에서는 지원되지 않는다. 이것은 반드시 CPL이 0일 때 실행되어야 하며 그래서 애플리케이션 프로그램에서 사용될 수 없다. LTR은 (TSS)를 가리키는 세그먼트 셀렉터와 함께 특별한 x86 작업 레지스터를 로드한다. LTR 명령어를 실행시킨 후 인자에 의해 가리켜지는 TSS는 busy로 설정되지만 하드웨어 작업 전환은 발생하지 않는다. LTR 명령어의 반대는 STR 명령어로서 작업 레지스터의 값을 특정한 위치에 복사한다. x86 작업 레지스터가 오직 LTR과 STR 명령어를 통해 직접 접근할 수 있다는 것에 주의한다. (ko)
- The LTR x86 instruction stands for load task register and is used in operating systems that support multitasking. LTR is supported only in protected mode and long mode, not in real mode or virtual 8086 mode. It must be executed when the Current Privilege Level (CPL) is 0, and therefore cannot be used by application programs. LTR loads the special x86 task register with a segment selector that points to a task state segment (TSS). After executing the LTR instruction, the TSS pointed to by the argument is marked busy, but no hardware task switch occurs.
* v
* t
* e (en)
|
dcterms:subject
| |
Wikipage page ID
| |
Wikipage revision ID
| |
Link from a Wikipage to another Wikipage
| |
sameAs
| |
dbp:wikiPageUsesTemplate
| |
auto
| |
date
| |
has abstract
| - The LTR x86 instruction stands for load task register and is used in operating systems that support multitasking. LTR is supported only in protected mode and long mode, not in real mode or virtual 8086 mode. It must be executed when the Current Privilege Level (CPL) is 0, and therefore cannot be used by application programs. LTR loads the special x86 task register with a segment selector that points to a task state segment (TSS). After executing the LTR instruction, the TSS pointed to by the argument is marked busy, but no hardware task switch occurs. The opposite of the LTR instruction is the instruction, which means store task register and copies the value of the task register to the specified location. Note that the x86 task register is only accessible directly through the LTR and STR instructions.
* v
* t
* e (en)
- LTR x86 명령어는 load task register 즉 작업 적재 레지스터를 의미하며 멀티태스킹을 지원하는 운영 체제에서 사용된다. LTR은 보호 모드와 롱 모드에서만 지원되며 리얼 모드나 가상 86모드에서는 지원되지 않는다. 이것은 반드시 CPL이 0일 때 실행되어야 하며 그래서 애플리케이션 프로그램에서 사용될 수 없다. LTR은 (TSS)를 가리키는 세그먼트 셀렉터와 함께 특별한 x86 작업 레지스터를 로드한다. LTR 명령어를 실행시킨 후 인자에 의해 가리켜지는 TSS는 busy로 설정되지만 하드웨어 작업 전환은 발생하지 않는다. LTR 명령어의 반대는 STR 명령어로서 작업 레지스터의 값을 특정한 위치에 복사한다. x86 작업 레지스터가 오직 LTR과 STR 명령어를 통해 직접 접근할 수 있다는 것에 주의한다. (ko)
|
prov:wasDerivedFrom
| |
page length (characters) of wiki page
| |
foaf:isPrimaryTopicOf
| |
is Link from a Wikipage to another Wikipage
of | |
is Wikipage redirect
of | |
is Wikipage disambiguates
of | |
is foaf:primaryTopic
of | |