The Palm Serial were 3 successive proprietary 10-pin Serial connectors on the bottom of the first 3 series of models of PDAs from Palm, Inc. to provide serial communications: 1) pre-IrDA models; 2) the 1st IrDA models; 3) the 1st thin, metal-body models. In addition to Palm's models (and rebranded models like the IBM WorkPad series) similar serial connectors have been used in the Ericsson MC16 Palmtop and Handera equipment.Pressing the HotSync button located at the base of the cradle closes a circuit between pins 2 and 7 which causes the activation of MUN2214 NPN transistor connected to pin 38 of the Motorola Dragonball CPU that provides a low signal on the IRQ1 UART, triggering the HotSync process.On pin 8 when a modem connects to the Palm similarly closes a circuit pin 2 to activate anot
Attributes | Values |
---|
rdf:type
| |
rdfs:label
| - Palm Serial (es)
- Palm Serial (en)
|
rdfs:comment
| - El Palm Serial es un conector propietario de 10 pines en borde de tarjeta situado en la base de los primeros modelos de PDA de Palm, Inc. para proporcionar comunicaciones por puerto serie. Además de en sus modelos (y en los equipos remarcados como la serie ), ha sido utilizado en el Palmtop y en equipos de Handera. En el pin 8 cuando se conecta un módem Palm se cierra de modo similar un circuito con el pin 2 que activa otro transistor MUN2214 NPN conectado al pin 32 (UART GPIO) de la CPU para notificarle la presencia del módem. (es)
- The Palm Serial were 3 successive proprietary 10-pin Serial connectors on the bottom of the first 3 series of models of PDAs from Palm, Inc. to provide serial communications: 1) pre-IrDA models; 2) the 1st IrDA models; 3) the 1st thin, metal-body models. In addition to Palm's models (and rebranded models like the IBM WorkPad series) similar serial connectors have been used in the Ericsson MC16 Palmtop and Handera equipment.Pressing the HotSync button located at the base of the cradle closes a circuit between pins 2 and 7 which causes the activation of MUN2214 NPN transistor connected to pin 38 of the Motorola Dragonball CPU that provides a low signal on the IRQ1 UART, triggering the HotSync process.On pin 8 when a modem connects to the Palm similarly closes a circuit pin 2 to activate anot (en)
|
name
| - Palm Serial Connector (en)
|
foaf:depiction
| |
dcterms:subject
| |
Wikipage page ID
| |
Wikipage revision ID
| |
Link from a Wikipage to another Wikipage
| |
Link from a Wikipage to an external page
| |
sameAs
| |
superseded by
| |
dbp:wikiPageUsesTemplate
| |
thumbnail
| |
designer
| |
PIN
| - CTS (en)
- ID (en)
- GND (en)
- N/C (en)
- RTS (en)
- RS-232 (en)
- VCC (en)
- HOTSYNC (en)
- RxD (en)
- TxD (en)
|
type
| - Communication, power supply (en)
|
has abstract
| - El Palm Serial es un conector propietario de 10 pines en borde de tarjeta situado en la base de los primeros modelos de PDA de Palm, Inc. para proporcionar comunicaciones por puerto serie. Además de en sus modelos (y en los equipos remarcados como la serie ), ha sido utilizado en el Palmtop y en equipos de Handera. De serie con los equipos se entrega una cuna de sincronización con el ordenador personal host (PC o Mac) o un cable de comunicaciones con algunos modelos. Al pulsarse el botón HotSync situado en al base de la cuna se cierra el circuito entre los pines 2 y 7 lo que provoca la activación de un transistor MUN2214 NPN conectado al pin 38 de la CPU Motorola Dragonball al que proporciona una señal baja en la IRQ1 UART, disparando el proceso de HotSync. En el pin 8 cuando se conecta un módem Palm se cierra de modo similar un circuito con el pin 2 que activa otro transistor MUN2214 NPN conectado al pin 32 (UART GPIO) de la CPU para notificarle la presencia del módem. (es)
- The Palm Serial were 3 successive proprietary 10-pin Serial connectors on the bottom of the first 3 series of models of PDAs from Palm, Inc. to provide serial communications: 1) pre-IrDA models; 2) the 1st IrDA models; 3) the 1st thin, metal-body models. In addition to Palm's models (and rebranded models like the IBM WorkPad series) similar serial connectors have been used in the Ericsson MC16 Palmtop and Handera equipment.Pressing the HotSync button located at the base of the cradle closes a circuit between pins 2 and 7 which causes the activation of MUN2214 NPN transistor connected to pin 38 of the Motorola Dragonball CPU that provides a low signal on the IRQ1 UART, triggering the HotSync process.On pin 8 when a modem connects to the Palm similarly closes a circuit pin 2 to activate another MUN2214 NPN transistor connected to pin 32 (GPIO UART) of the CPU to notify the presence of the modem. (en)
|
num pins
| |
pin10 name
| |
pin1 name
| - DTR output nonstandard (en)
|
pin2 name
| |
pin3 name
| - RS-232 input, Signal T RxD (en)
|
pin4 name
| |
pin5 name
| - RS-232 output, Signal R TxD (en)
|
pin6 name
| |
pin7 name
| - HotSync IRQ - +3.3 V to press the HotSync button (en)
|
pin8 name
| - Peripheral id. The Palm modem connects this pin to pin 2 to 20 kOhms ID (en)
|
pin9 name
| - is not connected. In the Palm III, 5 V DC output (en)
|
prov:wasDerivedFrom
| |
page length (characters) of wiki page
| |
foaf:isPrimaryTopicOf
| |
is Link from a Wikipage to another Wikipage
of | |
is superseded
of | |
is foaf:primaryTopic
of | |