About: Surface differential reflectivity     Goto   Sponge   NotDistinct   Permalink

An Entity of Type : owl:Thing, within Data Space : dbpedia.demo.openlinksw.com associated with source document(s)
QRcode icon
http://dbpedia.demo.openlinksw.com/describe/?url=http%3A%2F%2Fdbpedia.org%2Fresource%2FSurface_differential_reflectivity&invfp=IFP_OFF&sas=SAME_AS_OFF

Surface differential reflectivity (SDR) or differential reflectance spectroscopy (DRS) is a spectroscopic technique that measures and compares the reflectivity of a sample in two different physical conditions (modulation spectroscopy). The result is presented in terms of ΔR/R, which is defined as follow: where R1 and R2 represent the reflectivity due to a particular state or condition of the sample. where ε1 = 1 is the vacuum dielectric constant and ε3 = ε’3 - iε”3 is the bulk dielectric function.

AttributesValues
rdfs:label
  • Surface differential reflectivity (en)
rdfs:comment
  • Surface differential reflectivity (SDR) or differential reflectance spectroscopy (DRS) is a spectroscopic technique that measures and compares the reflectivity of a sample in two different physical conditions (modulation spectroscopy). The result is presented in terms of ΔR/R, which is defined as follow: where R1 and R2 represent the reflectivity due to a particular state or condition of the sample. where ε1 = 1 is the vacuum dielectric constant and ε3 = ε’3 - iε”3 is the bulk dielectric function. (en)
dcterms:subject
Wikipage page ID
Wikipage revision ID
Link from a Wikipage to another Wikipage
sameAs
dbp:wikiPageUsesTemplate
has abstract
  • Surface differential reflectivity (SDR) or differential reflectance spectroscopy (DRS) is a spectroscopic technique that measures and compares the reflectivity of a sample in two different physical conditions (modulation spectroscopy). The result is presented in terms of ΔR/R, which is defined as follow: where R1 and R2 represent the reflectivity due to a particular state or condition of the sample. The differential reflectivity is used to enhance just the contributions to the reflected signal coming from the sample. In fact, the light penetration (α−1) inside a solid is related to the adsorption coefficient (α) of the material. The contribution of the sample surface (e.g., surface states, ultra-thin and thin deposited films, etc.) to the reflected signal is generally evaluated in the 10−2 range. The difference between two sample states (1 and 2) is thought to put in evidence small changes occurring onto the sample surface. If R1 represents a clean freshly prepared surface (e.g., after a cleavage in vacuum) and R2 the same sample after the exposure to hydrogen or oxygen contaminants, the ΔR/R spectrum can be related to features of the clean surface (e.g., surface states); if R1 is the reflectivity spectrum of a sample covered by an organic film (even if the substrate is only partially covered) and R2 represents the optical spectrum of the pristine substrate, the ΔR/R spectrum can be related to the optical properties of the deposited molecules; etc. The experimental SDR definition reported was interpreted in terms of surface (or film) thickness (d) and its dielectric function (ε2 = ε’2 - iε”2). This model, which assumes the surface as a well-defined phase above a bulk, is known as the “three-layer model” and states that: where ε1 = 1 is the vacuum dielectric constant and ε3 = ε’3 - iε”3 is the bulk dielectric function. The SDR measurements are generally realized by exploiting an optical multichannel system coupled with a double optical path in the so-called configuration. In this configuration, the ΔR/R signal is obtained by a direct comparison between the reflectivity signal R1 arises from the sample (e.g., a silicon substrate covered by a few amount of molecules) placed inside the UHV chamber (first optical path) and the R2 signal acquired from a reference sample (dummy sample; e.g., a silicon wafer) placed along the second optical path. The difference between R1 and R2 is due to the deposited molecules, which can affect the reflectivity signal in the 10−3÷10−2 range of the overall reflected signal of the real sample. Consequently, a high signal stability is required and the two optical paths must be as comparable as possible. The SDR apparatus was firstly described and used by G. Chiarotti for the investigation of the surface states contribution in the Ge(111) reflectivity properties. This work also represents the first direct evidence of the existence of surface states in semiconductors. An evolution of the SDR set-up by using linearly polarized light was firstly described by P. Chiaradia and co-workers for testing the structure of the Si(111) 2 × 1 surface. Other equivalent SDR set-up have been exploited for studying: the surface roughening evolution, the reactivity of halogens with semiconductor surfaces, the adhesion of nanoparticles during their growth, the growth of heavy metals on semiconductors, the nano-antennas characterization, just to mention some of the works related to this surface optical technique. (en)
prov:wasDerivedFrom
page length (characters) of wiki page
foaf:isPrimaryTopicOf
is foaf:primaryTopic of
Faceted Search & Find service v1.17_git139 as of Feb 29 2024


Alternative Linked Data Documents: ODE     Content Formats:   [cxml] [csv]     RDF   [text] [turtle] [ld+json] [rdf+json] [rdf+xml]     ODATA   [atom+xml] [odata+json]     Microdata   [microdata+json] [html]    About   
This material is Open Knowledge   W3C Semantic Web Technology [RDF Data] Valid XHTML + RDFa
OpenLink Virtuoso version 08.03.3330 as of Mar 19 2024, on Linux (x86_64-generic-linux-glibc212), Single-Server Edition (378 GB total memory, 56 GB memory in use)
Data on this page belongs to its respective rights holders.
Virtuoso Faceted Browser Copyright © 2009-2024 OpenLink Software